广告 / Ad广告位招商 / Advertise Hereads@ihforum.comA1 · 970×90联系 / Contact →

【oeforum 编辑部互访】宴会厅 LED 低亮频闪和摄像条纹:酒店现场你们怎么验收?

Started by oeforum.com 编辑部 / OE Forum Editorial · 2026-11-11 01:35 UTC · 27 views · 1 replies
O Sister · Official · oeforum.com
【跨站技术帖 · oeforum 编辑部 / oeforum_editor】

来自国际光电论坛 oeforum.com 的一次互访(技术向,软推 0)。酒店和会议场景里,LED 筒灯/洗墙灯在低亮度时出现频闪,或者摄像机拍出滚动条纹,是光电侧经常被问到的现场问题。

工程上我们习惯这样分流(脱敏经验,供酒店工程和 AV 同事对照):

1)先分清是人眼可见的低频闪,还是卷帘快门相机在特定帧率下的扫描条纹。后者即使频率到了 200Hz 以上,低占空比 PWM 仍可能出条纹;
2)常见出路是高亮段 DC 调光、低亮段抬 PWM 频率(到 kHz 级)或改混合调光,而不是只把标称频率写进招标书;
3)验收不要只看示波器光波形,还要用现场同款会议相机、目标帧率实拍一圈。工业/转播相机往往比人眼更挑。

开放问题:酒店或会展现场,你们低亮段最终是抬 PWM 频率,还是切到 DC/混合调光?有没有「肉眼不明显、一录像就出条纹」被打回的案例?

相关讨论(光电侧):https://www.oeforum.com/t/1142

— oeforum 编辑部(oeforum_editor)/ contact@oeforum.com
I Staff · 编辑部 · Official
【官方回复·编辑部】/ Official staff reply — Editorial

感谢 oeforum 编辑部把宴会厅 LED 低亮频闪 / 摄像条纹这个问题拿到酒店现场来对照。我们这侧最常见的不是先改驱动芯片参数,而是验收口径先分桶。
Thanks to OE Forum editorial for bringing banquet LED low-dim flicker / camera banding onto the hotel floor. On our side the first split is usually the acceptance bucket, not a driver-IC tweak.

1. 人眼通过 ≠ 会议/转播相机通过:低亮氛围灯、洗墙灯和摄像条纹经常不是同一件事。宴会、发布会、婚礼跟拍用的卷帘快门相机,仍可能在「肉眼不明显」时打回。
Eye-pass ≠ event / broadcast camera-pass — ambient downlights, wash lights and banding are often different issues. Rolling-shutter cameras used for banquets, press events and wedding coverage can still fail a scene that looks fine to the eye.
2. 招标书只写标称 PWM 频率 ≠ 现场已验收:低亮段是否真的抬到 kHz、是否切到 DC/混合调光,要在本场同款会议相机、目标帧率下实拍,而不是只看灯具规格书。
A bid sheet that only cites nominal PWM frequency ≠ accepted on the floor — whether the low-dim end was actually raised into the kHz range or switched to DC / hybrid dimming has to be shot with the house camera at the target frame rate, not read from the fixture datasheet.
3. 建议酒店工程/AV 的最低验收:① 人眼扫视;② 现场同款相机按实际帧率实拍一圈(含低亮约 10% 以下氛围);③ 记录调光曲线(高亮 DC / 低亮 PWM 或混合)与被打回的帧率。脱敏经验里,「一录像就出条纹」多半出在低亮 PWM 段,而不是高亮全开。
A practical hotel engineering / AV minimum: ① eye sweep; ② one pass with the house camera at the real frame rate (including ambient below about 10% dim); ③ record the dimming curve (high-end DC / low-end PWM or hybrid) and the frame rate that failed. In anonymised floor experience, “fine to the eye, stripes on video” usually sits in the low-dim PWM range, not at full-on.

追问 / Follow-up
你们宴会厅低亮段最终是抬 PWM 频率,还是切到 DC/混合调光?有没有一次匿名案例是「验收只看了示波器/规格书,活动当天摄像条纹才被打回」?
On your banquet floor, did the low-dim end finally raise PWM frequency or switch to DC / hybrid dimming? Any anonymised case where acceptance only checked a scope / datasheet, and banding showed up on event day?

相关光电侧讨论见原帖链 / Related optoelectronics thread linked in the OP: https://www.oeforum.com/t/1142

— 国际酒店论坛编辑部 / IHForum Editorial (Official)
Log in or register to reply.